Dear Carlos,
thanks for sharing the lime-report results!!!
The interesting lines seem to be these ones:
daemon.err mount_root: failed - mount -t jffs2 /dev/mtdblock5
/rom/overlay: Not a tty
kern.err kernel: [ 102.551190] Too few erase blocks (4)
Looking on the internet for the second one, I found this page:
https://openwrt.org/faq/too_few_erase_blocks
Basically it says that the image file is too large.
Also, I found this old email where it is indicated that just 8 MB of the
16 MB flash memory can be used (I am not sure if this is still right):
https://lists.infradead.org/pipermail/openwrt-devel/2019-April/022260.html
You should be able to build a smaller image using the image selector and
removing things like lime-app and lime-debug, but right now it does not
work for me.
https://repo.libremesh.org/selector/?version=2024.1-rc1-ow23.05.3-default&target=ath79%2Fgeneric&id=comfast_cf-e313ac
Can you compile an image locally:
https://libremesh.org/development.html#compiling_libremesh_from_source_code
Ciao!
Ilario
On 12/29/24 19:13, Carlos Flores via LibreMesh wrote:
> Hello everyone again.
>
> Apologies for the delay in responding, but I’ve been quite busy these
> days, which has prevented me from running the tests. Many thanks to
> Ilario and Pony for your responses.
>
> I’ll share the tests I’ve had done:
>
> Firmware 2023-rc2. We installed it on two antennas and it works
> correctly. The antennas connect to each other, the lime-app works with
> two antennas on the network, and the configurations are saved correctly.
> The wifi LED blinks from a clean installation, indicating that the
> hardware is active. Attached lime-report for this version. df results:
>
> root@LiMe-7f62e1:~# df
> Filesystem 1K-blocks Used Available Use% Mounted on
> /dev/root 5120 5120 0 100% /rom
> tmpfs 28412 108 28304 0% /tmp
> /dev/mtdblock5 448 256 192 57% /overlay
> overlayfs:/overlay 448 256 192 57% /
> tmpfs 512 0 512 0% /dev
>
>
> Firmware 2024-rc1-mini: We verified that the file system works
> correctly, saving the configurations. We couldn't activate the hardware.
> The wifi LED is off. df results:
>
> root@LiMe-7f62e1:~# df
> Filesystem 1K-blocks Used Available Use% Mounted on
> /dev/root 4096 4096 0 100% /rom
> tmpfs 28292 116 28176 0% /tmp
> tmpfs 28292 88 28204 0% /tmp/root
> tmpfs 512 0 512 0% /dev
> /dev/mtdblock5 1472 232 1240 16% /overlay
> overlayfs:/overlay 1472 232 1240 16% /
>
>
> Firmware 2024-rc1: As I mentioned, the system loads into RAM. lime-
> report attached. Df results:
>
> root@LiMe-7f62e1:~# df
> Filesystem 1K-blocks Used Available Use% Mounted on
> /dev/root 5376 5376 0 100% /rom
> tmpfs 28292 108 28184 0% /tmp
> tmpfs 28292 132 28160 0% /tmp/root
> overlayfs:/tmp/root 28292 132 28160 0% /
> tmpfs 512 0 512 0% /dev
>
>
> I’m not sure if it’s better to write on the forum instead of by email.
>
> Thanks in advance and merry christmas!
>
> --
>
>
> Carlos Flores Álvarez
>
> Cofundador y Director de Innovación
>
>
> CREÁTICA
>
> el Hub - Calle Rocafort 101, Bajo. 28021 MADRID
> *Movil: 675 857 112 • Skype: carlos@??? *
>
> carlos@??? <mailto:carlos@asociacioncreatica.org> •
> www.creatica.ong <http://www.creatica.ong>
>
--
Ilario
iochesonome@???
ilario@???
